top of page

Alll the work is done in certified  facilities, not only using state of the art manufacture process, but allowing our mechanics to completely control the rebuild process keeping quality at its highest. Our mechanics and machinists are fully-trained professionals who pride themselves on the quality of work and level of service we provide our customers.

Re- Manufacturing
 

Every  re-manufactured engine we build begins with thorough cleaning, inspection and machining of all re-manufacturable castings. All cast iron components are magnaflux to guarantee integrity. Engine blocks are precision bored, decked and diamond honed to the specified RMS. Crankshafts are ground and polished to an 8-12 RMS finish. Valve seats are precision cut to three angles, and heads are resurfaced and vacuum tested. The following components are replaced as part of the manufacturing process:

  • New Pistons

  • New Rings

  • New Timing Components

  • New Freeze Plugs

  • New Installer Gasket Set

  • New Main Bearings

  • New Rod Bearings

  • New Cam Bearings

  • New or Reground Cam Shaft Cam core may apply

  • New Hydraulic Lifters

  • New Oil Pump

  • Remachined Block, Crank Shaft, Connecting Rods and Cylinder Heads

01

02

Machine Shop Services
 

Valve Job

All vales get re-faced.  Valve seats get 3 angle valve job. To find out more about our valve job services or to make an appointment, call us to speak to one of our team members.

Cylinder Head Pressure Check

Pressure testing is the best method of testing for cracks because cracks in areas that are not visible can still be found.

MagnaFlux

For cast iron engine components, MagnaFlux will highlight any cracks that may otherwise not be seen.  

Bore and Hone Engine Block

Our automotive machine shops uses special equipment to bore the block over-sized and hone the surface of the cylinder wall. 

Cylinder Head Surfacing

Compared to most automotive machine shops, MJM does not use belt sanders to surface the cylinder head. But instead, we use a CBN surfacer that is necessary to meet the tight tolerances required by today's engines.

Crankshaft Grinding

When a crankshaft is turned to an undersize, it can and does change the stroke and degrees apart of each rod journal. To index a crank, first the machinist has to know where the stroke and degrees (swing) are. Once this is established, with the right machine to start with, the crankshaft can be indexed for both swing and stroke. Crankshafts that are ground to within +or- .0001 (that's one ten thousands of an inch) on rods and mains gives you a crankshaft that will give you full bearing contact with a lot longer life. If you want more strength and longevity from your engine this is a must.

Crank Kits

Crank Kit includes a new or re-ground crankshaft, rod and main bearings with thrust washers. 

Engine Kits

All of our engine kits come with name brand high quality components. If you need an engine master kit, re-ring kit, cam kit, or block kit, please call us today.

Aluminum Welding

When it comes to welding aluminum we are the professionals to do your job. With over 18+ years of aluminum welding experience you can trust that the job is done right.

Short Blocks

All of the engine block sub-assemblies consisting of all of the related internal components are rebuilt and installed. The short block engine is normally just the rebuilt block containing pistons with rings and a crankshaft kit with bearings a new cam shaft.

Long Blocks

Consists of cylinder block fitted with pistons, rings, connecting rods, crankshaft and all bearings, cylinder heads, camshaft, timing chain, belt and/or sprockets.

03

Our Technicians
 

We only hire  technicians who have at least 10 years of experience rebuilding engines. The knowledgeable and expert ability of our staff to remove, disassemble and reassemble engines at a higher level of precision and cleanliness is guaranteed. In addition, our engine suppliers provide only the highest quality engine parts and state of the art engine machining equipment. All of our suppliers have been remanufacturing engines for several decades.

Get your vehicle back on the road with Engine Remands Engines’ experienced technicians, top of the line engine parts and better prices!

04

Included In Rebuild
 

  • New water pumps

  • Thermostats

  • Radiator Test

  • Anti-freeze/coolant

  • Clean and rod out radiator

  • Double platinum spark plugs

  • Computer Scan

  • Oil – filter

  • 5 Hour Testing upon completion

  •  

    Free Checkup 2 times per year $195 Value

     

     

     

     

     

05

Engine Maintenance & Our 3 year Warranty
 
Preventive maintenance is critical to the engines lifespan. Like other auto parts, most car engines aren't built to last forever. However, you can increase the engine's lifespan by performing regular preventive maintenance. The easiest way to maintain peak performance and fuel economy is to provide regular engine maintenance for your vehicle. To have your engine maintained by our experts - Thogether as a parnership we will keep the engine in top performance and this is how we are able to offer a 3 year Warranty..
 

© 2023 by YOU DRIVE IT WE BUILD IT.​ Proudly created with Wix.com

  • Instagram
  • Google Square
  • Twitter Square
  • facebook-square
bottom of page